Meister Werks 2.0T Reinforced Oil Pan

Meister Werks 2.0T Reinforced Oil Pan is designed for lowered or air bagged vehicles. These pans will prevent you from rubbing though the steel OEM pan and prevent damage to the oil pan. These pans will save your oil pan drain and bung from being disfigured if you scrape. Our reinforced oil pan have 3/16″ / 5mm steel plates welded to the pan and are also designed to bend incase of a hard impact.

This pan can take heavy impacts, however these impacts may damage the pan. The pan WILL save your engine. We design these pans this way so the full impact transfers to the hot roll steel plate and not to the engine block. This will prevent the block from being damaged.

Power Coated Pan & More

Our pans are also powder coated wrinkle red. We do this incase you do his something the oil will be visible and you will be able to see if the pan is leaking.

If your car does not have a oil sensor, you have the option to add one. We can also provide you with bolts and silicone gasket.

Click here to order your pan today.

Powder Coating Harley-Davidson Parts

Our long time friend Pete came in last week for powder coating Harley-Davidson chrome parts for his motorcycle bike. Since we can not powder coat directly over chrome, we knew we had a challenge.

We would need to etch the chrome in some way for the powder to stick. We ended up media blasting the chrome with 34 grit aluminum oxide. This takes about four times longer than any other material to etch.

We set up our automated media blaster with rotisserie to blast his items for about an hour. After that done, we did touch ups for around 30 minutes to get everything even and etched properly. We then cleaned and prepped the surface throughly and hung the parts for powder coating. We use Cardnal Industrial Finishes, BLACK Super Durable 90 Gloss, color code P009-BK180. This extremely glossy powder will withstands the riggers of the road and lasts five times longer than any other powder. As you can see the finish and the glossiness is pretty amazing.

To make an appointment to have us do powder coating Harley-Davidson parts, call 425-254-0627 – Ex 0, or email us. Meister Werks European & Import is located one block south from The Renton Landing in Renton, WA.

 

Lending Now Available at Meister Werks!

Financing now available at Meister Werks. MW have partnered with Snap and Lendmark. We offer these solutions so we can get your car back on the road and help out our customers keep their cars in tip top shape. We understand, sometimes repairs are financially difficult to get done. With these solutions it makes it easier to break it down over a longer period of time.

With Snap, they offer up to $3000 in financing for your car repairs, maintenance or custom work. No credit checks needed. They will also authorize up to 10% additional for the amount you are approved for as well. After your car repair is complete, all you have to do is pay the $39 processing fee and we will handle the rest. When you pick repaired vehicle up, the payments are made directly to Snap. You can choose to pay, weekly bi-monthly or monthly. The money is then directly withdrawn from your bank account.

Lendmark does it a little differently and does require a credit check. However your interest may be lower and there is no cap on what they will lend. They also have a portal very soon and you will be able to get approved within 15 minutes.

Contact us or call 425.254.0627 if you have any questions.

Mounting and Balancing Tires on Flat Lip 3 Piece Wheels

We regularly receive jobs in the shop for mounting and balancing tires for flat lip, 3 piece wheels. This can pose a challenge as the back barrels do not have a drop for us to dismount the tire properly.

When performing this service, we have to remove the face side tire first. We always use the Motion Pro Rim Shield guards to protect the wheel lips. After that, we remove the tire from the machine. Using the bead breaker, we push the rest of the tire off into the tire well or tire drop portion of the wheel. Once this is achieved, we return the wheel and tire to the machine and remove the rest of the tire. Mounting can also be challenging, but in this video instance, there was not a problem. People with stretched tires will have more issues getting them to bead on the wheel lip beads correctly.

Even though this video is sped up, this requires more labor to remove the tire. We charge an hourly rate for all custom 3 piece wheels. If you have a standard wheel, made by your vehicle’s manufacturer, there is no need to worry. There will not be any additional charge for standard wheels.

With a purchase of tires at Meister Werks, we also offer free flat repair, free tire rotation and we will warranty your tires if there is a warranty issue with the manufacturers milage warranty. Anther service we offer is wheel alignment. On our state of the art 3d laser alignment machine, we will be able to dial in your alignment. This will eliminate unnecessary tire wear and prolong the life of your tires.

To make an appointment to have your tires changed, call 425-254-0627 or email us. Meister Werks European & Import is located one block south from The Renton Landing in Renton, WA.

Painting Brake Calipers

This week we performed some custom work, painting brake calipers on a 2008 Maserati Ghibli Q4. The process takes about 12 hours to do it the right way. Prep is key to making these calipers turn out like this. 1) Removing as much brake dust, dirt and grime and 2) High quality products.

First we will remove the wheels, brake rotors and pads. Next we do prep, lots and lots of prep. We can not do enough prep. If there is any brake dust on the calipers, the primer will not adhere correctly and you will see it. We also mask the entire car, incase of over spray,. We also mask the suspension components, ABS / sensor wires and brake fluid lines. After all the prep and masking is done, we spray 3 coats of acid based self etching primer on the calipers.

We let that set up and cure per the manufacture’s instruction, then start painting the brake calipers. Painting brake calipers takes time. Applying many light coats is the another key to a quality finish. The paint we use is a ceramic based high temp paint (900º) that will hold up to the heat. We let that set up for many hours before starting on the next step. When the paint has sets up, we install the Maserati decals. We use 3m cast vinyl that has a very long life, UV stable and is extremely thin. The clear coat will protect the decals and will last the life of the calipers. Lastly, we spray the calipers with ultra gloss, glamour 2 part clear coat. Again, many coats is the key to this amazing finish.

After everything cured over night, we were able to reassemble the brakes. We check the brakes and make sure everything is functional, exactly like when the vehicle arrived at the shop.

If you would like your brake calipers painted with the same results, contact us. Call 425-254-0627 or email us. Meister Werks European & Import is located one block south from The Renton Landing in Renton, WA.

 

 

 

Performance Tune – 2018 Golf R

Performance Tuning the Golf R

Today we installed a stage 1+ performance tune on our customer’s 2018 Volkswagen Golf R. The procedure is simple and takes about an hour of time for us to complete each tune. The new performance tune will give him an additional 83hp / 70 Ft Lbs of torque, with no other modifications needed. This tune will also optimize the 1/4 throttle range, so while driving in traffic or with the cruise control on, he will see better fuel economy. Just as long as he keeps his foot off the throttle.

Tuning the 2018 Gold RThe customer also has an Automatic Shifting Manual Transmission (ASMT or DSG) in his Golf R. With the engine performance tune, it requires an additional tune for the transmission control module. Not only does it need this for the additional horse power, but it also optimized the shifts timing and removes the gear kick down. Kick down happens when breaking or slowing while turning. This is a common complaint from owners with a DSG transmission.

In just under a two hours, our customer now has 375hp with 350tq and will be getting fuel economy. Additionally, he purchase a Uniconnect+ cable which will allow him to upgrade to a stage 2 at home, scan his car for fault codes and clear them if needed.

For more information, you can go to the Unitronice’s website to see what we can do for your vehilce. To make an appointment for a performance tune, call 425-254-0627 or email us. Meister Werks European & Import is located one block south from The Renton Landing in Renton, WA.

 

How to Prep Parts for Powder Coating Correctly

Left part after chemical stripping, right after chemical stripping and media blasting. This is how the left part should have looked and why the powder flaked off.

This weekend, our good customer Keith dropped off a few items he needed powder coating correctly applied for his 2014 Subaru Impreza show car.

The bumper canards Keith purchased from an aftermarket parts company coated them satin black. As he was installing the parts onto his car, the powder started flaking off around the screw holes. Immediately he knew that he needed to get them recoated and have them powder coated correctly.  Keith called us on Thursday and we told him we would need to strip them back to bare metal and correctly prep them for powder coating correctly.

Keith’s 2014 Subaru Impreza Before Installing Parts

We chemically stripped them and after 5 minutes, we knew they were not prepped the right way. As you can see in the photo, the part on the left is how the company coated the part. The part on the right is what the left should have looked like and taken about 30 minutes to chemical strip. The part on the right was media blasted at Meister Werks with 36 grit aluminum oxide. This will give the powder ‘bite’ and allow it to stick much better than the smooth surface seen on the left part. This exactly why you can not powder coat over chrome. There is nothing for the powder to stick to and will flake off almost immediately.

The next time you need your project done correctly, call Meister Werks. We do large production runs and single items as well. We also shoot satin black almost every Friday as a part of our Black Friday special. To make an appointment or with any questions, call 425-254-0627 or email us. Meister Werks European & Import is located one block south from The Renton Landing in Renton, WA.

After Powder Coating

After Installation

After Installation

 

Meister Werks Repair, 24-7

At Meister Werks, we are always available for our customers if you have an urgent repair. To message us after hours you can go to our google page on your mobile devise, 24 hours a day, 7 days a week. You can also email us and we will reply as soon as possible.

If you are towing in your vehicle, you can use google messagingemail or contact us via our contact page. No need to get an approval. Just tow or bring in your vehicle and drop it off in front of our shop. We would be happy to look at your car the next business day and get you back on the road.

To contact us during business hours just call on our main line, 425.254.0627 or email us. If we don’t pick up, please just leave a message and we’ll get back to you promptly.

To make an appointment, call 425-254-0627 or email us. Meister Werks European & Import is located one block south from The Renton Landing in Renton, WA.

About Us

The owner and of our company, Dave Meister, has always been a car enthusiast. Since age 16, he has had a passion for modifying and working on European cars.  What is now Meister Werks began in 1997, with Dave manufacturing and selling custom gauge faces to fellow car enthusiast and friends with VW, Audi, and Porsche vehicles.

As our business has grown over the years, our products and services have expanded as well to keep up with customer demand. Now a full service shop, we will take the time to explain your vehicles’ needs to ensure you have a confident and positive experience. To provide you with the best experience possible, we only hire staff with the widest knowledge and best work ethic. Our passion for excellence has resulted in satisfied customers. Customer service is our number one goal—if you’re not happy, we’re not happy. If you live in the Pacific Northwest, make us your go-to shop for European automotive service and repairs.